xt1060救砖问题

波多尔死机

先前发错地方了，现在转发过来。。

32g未解锁xt1060未root，作为备机养电信卡使用，ota升级到5.1过后正常使用了一段时间，偶然发现自动关机，以为只是电量耗尽，可充电也没有反应不能开机。按论坛http://bbs.ihei5.com/thread-398875-1-1.html步骤处理，QHSUSB驱动安装正常，最后命令符提示如下，仍然没法开机，试过拆机扣掉电池重新链接/换电脑都不行，就放抽屉没管了，前两天闲着没事想起，淘了一块电池换上，依然黑屏，请教各位老大这种现象还有救没？



C:\Users\yf-03\Desktop\blankflash>qflash.exe -com10 -ramload MPRG8960.hex -mbn 33 MSM8960_bootlo
ader_singleimage.bin -v -o
Motorola qflash Utility version 1.3
COMPORT      :COM10
RAMLOADER    :MPRG8960.hex
type is 0x21
7 mbn file name MSM8960_bootloader_singleimage.bin type 33
verbose mode on
Motorola qflash dll version 1.6
RAMLOADER VERSION: PBL_DloadVER2.0
------------------------------------------------------
DEVICE INFORMATION:
------------------------------------------------------
Version       : 0x8
Min Version   : 0x1
Max Write Size: 0x600
Model         : 0x90
Device Size   : 0
Description   : Intel 28F400BX-TL or Intel 28F400BV-TL
------------------------------------------------------
Using passed in packet size, changing from 0x600 -> 0x600
EXTENDED_LINEAR_ADDRESS_REC @ 0x2a000000
Write 65536 bytes @ 0x2a000000
100EXTENDED_LINEAR_ADDRESS_REC @ 0x2a010000
Write 11840 bytes @ 0x2a010000
100START_LINEAR_ADDRESS_REC @ 0x2a000000
EOF_REC
Sleeping for 3s
sdl_hello() - Invalid response: 7e030003331b7e
sdl_hello() - This is a NAK response from ROM code, which means the device has been reset back t
o blank flash mode. Usually this is caused by power supply issues. Please try again with battery
eliminator if it persists
RAMLOADER VERSION: PBL_DloadVER2.0
------------------------------------------------------
DEVICE INFORMATION:
------------------------------------------------------
Version       : 0x8
Min Version   : 0x1
Max Write Size: 0x600
Model         : 0x90
Device Size   : 0
Description   : Intel 28F400BX-TL or Intel 28F400BV-TL
------------------------------------------------------
Using passed in packet size, changing from 0x600 -> 0x600
EXTENDED_LINEAR_ADDRESS_REC @ 0x2a000000
Write 65536 bytes @ 0x2a000000
100EXTENDED_LINEAR_ADDRESS_REC @ 0x2a010000
Write 11840 bytes @ 0x2a010000
100START_LINEAR_ADDRESS_REC @ 0x2a000000
EOF_REC
Sleeping for 3s
sdl_hello() - Invalid response: 7e030003331b7e
sdl_hello() - This is a NAK response from ROM code, which means the device has been reset back t
o blank flash mode. Usually this is caused by power supply issues. Please try again with battery
eliminator if it persists
RAMLOADER VERSION: PBL_DloadVER2.0
------------------------------------------------------
DEVICE INFORMATION:
------------------------------------------------------
Version       : 0x8
Min Version   : 0x1
Max Write Size: 0x600
Model         : 0x90
Device Size   : 0
Description   : Intel 28F400BX-TL or Intel 28F400BV-TL
------------------------------------------------------
Using passed in packet size, changing from 0x600 -> 0x600
EXTENDED_LINEAR_ADDRESS_REC @ 0x2a000000
Write 65536 bytes @ 0x2a000000
100EXTENDED_LINEAR_ADDRESS_REC @ 0x2a010000
Write 11840 bytes @ 0x2a010000
100START_LINEAR_ADDRESS_REC @ 0x2a000000
EOF_REC
Sleeping for 3s
sdl_hello() - Invalid response: 7e030003331b7e
sdl_hello() - This is a NAK response from ROM code, which means the device has been reset back t
o blank flash mode. Usually this is caused by power supply issues. Please try again with battery
eliminator if it persists
Unexpected target reset, bailing out after 2 retries
C:\Users\yf-03\Desktop\blankflash>

老子额安逸了

有救的，联系我微信690131433